Tech Tip - Wire Rims going Tubeless

Flats aren't all that common in today's driving experience. Neither are inner tubes. I believe there to be a direct correlation.

The Daytona wire wheels on my Sunbeam Alpine left me with two flats during our journey to and from the United this past year. Combine the general inconvenience of a flat with the grim prospect of finding a replacement tube (plus a shop that is willing to even consider working on a wire wheels), and you have a formula for disaster.  Because tubeless tires have a patterned rough surface rather than a smooth surface, I was finding that the inner tubes were subject to abrasions from the insides of the tires themselves.  The failure points were always on the outside diameter of the tube.

If only there was a way to go tubeless! In consulting some other British car club forums, I discovered that there was success in sealing the rims. Armed with the confidence that this technique worked for Barney Gaylord, I set out to apply the concept to my Sunbeam Alpine's wire wheels.

I decided to make the attempt using what others had found success with.  This involved careful cleaning and a coating with some sealant.  3M makes a product for Marine applications called 5200.  It takes a week to cure and is naturally water and air tight with good flexibility.

Since these rims are chromed it was easy to remove the rim strap tape and remove any residue with parts cleaner.  The final wipe-down was done with brake cleaner.  The Marine sealant applies with a normal caulking gun.  The trick is to get it on evenly without waste or bumps.  I made a special spatula tool from a piece of plastic, notched to produce a uniform application depth.

Left for a day or so to cure, I then applied a layer of 1 inch wide 3M "helicopter" polyurethane protective tape.  This flattened the layer of sealant and also protected its surface against the pressure of the tire bead.  The layer doesn't have to be thick, just enough to keep it all in place and fill the spoke nut holes.  Then it was left to sit for the rest of the week in a warm environment.  The squeezed-out excess was easily trimmed away with a razor knife once everything had cured.

To keep the outer edge of the rim with its newly sealed surface and tape protected, I decided to install the tires from the rear side.  This was accomplished easily with my No-Mar Tire Changer.  Getting the beads to hold air initially was another matter.  I had to put the tire on an elevated platform supported by the outermost diameter of the tire and stand on the center of the wheel.  Since I'm a bit of a lightweight, I also took advantage of pushing myself down on the tire by trying to lift the house by the garage ceiling rafters.  ;-)  The tire lube I use is so slippery the beads wanted to pop out on one side and go in on the other.  After a few expletives and further physical exertion the tire beads were up against their sealing surfaces of the rim and could hold air.

Two days later they're still holding air.  So I'd call this experiment a success.  Considering that Barney said he autocrosses with his sealed in this manner I probably don't have anything to worry about.  Look out Georgia, here we come!

I'll carry a few inner tubes just in case... someone else needs one.

Sunbeam S7 - Wheel Bearing Grease Seals

The Sunbeam S7 Deluxe originally used Angus 182 leather grease seals on the wheel bearings.  While surprisingly long-lived (12,000 some odd miles and 66 years of service) everything is prone to  eventual failure.  This weekend while taking a leisurely trip to visit J&B Moto Company, the rear grease seal lost structural integrity.  Grease was all over the rear wheel and caked into the mud guard.

A quick look for a replacement yielded a modern equivalent.  A Precision 476838 Seal was a perfect fit.  It is a double lip seal and should yield adequate protection.  I doubt they will last over 60 years though.

The old seal is easily pushed out with two sockets of appropriate size.  The new seal is pushed just as easily with one socket.  If the seal becomes cocked in the hole it is very difficult to push.  I chose to use my drill press as a light-duty press for this job since it is easy to line up for a perfectly even press job.  (drill motor off of course)

Remember the castle nut of the seal assembly is LEFT-handed, just like the axle.

Honda CX500 - "fantastinen" Finnbox FBG47 CDI ignition

Problem Statement:

Honda doesn't produce the CDI ignition module for the early CX500 motorcycles.  The capacitors and semiconductors are now over 30 years old and probably not performing as they did when they were new.

These are the symptoms my CX500 was beginning to experience:

• Hard Starting
• Misfire while on choke
• "Flat" spots in the rev range
• Hesitation from idle
• Misfire while accelerating hard
• Total loss of power in the rain

As a benchmark, the bike was getting around 48mpg with backroad and commuting to work type of driving.

Naturally the carburetors were eliminated as a culprit.  They have been cleaned, rebuilt, balanced, and tweaked repeatedly.  The spark coils were replaced with new modern ones from an ATV.  The spark plugs were changed to a resistor type plug and the resistors were eliminated from the caps.  These upgrades only provided marginal improvement.  The bike no longer ran on one cylinder at start, but still had all the other problems.

I also checked the stator and source coil winding to make sure they were healthy.  

I had the whole engine out over the winter, so checking the resistance readings was easy.  The insulation was good, so I had no doubts that the G47 stator was in good health.

I started reading about the ignition module and found this post on the CX/GL500 forum.  This seemed like the appropriate solution.

(There was also a Ignitech option, which was computer programmable, and cost several hundred dollars.  This wasn't something that I was interested in.)

The Solution:

I contacted "Andy62" from the forum and he replied swiftly confirming that he could happily make a Finnbox FBG47 for me.  Like any good engineer he had decided to make what he could not purchase.  The result is a re-engineered version of the CDI ignition module similar to the original, but unique with modern components.  A few short weeks later it showed up in the mail from Finland.  The exchange of emails between Aki and myself was pleasant and I'm very grateful for his dedication and stewardship to support the Honda CX500.

... and was promptly installed

It is a well engineered product, for something that wasn't supposed to be a commercial venture.  As enthusiasts we are indebted to people like this that use their talents to support old equipment.  The board is professionally created, and the components are thoughtfully arranged and packaged.  The whole module is enclosed in a tough water-tight enclosure, with the leads coming out sealed nicely.

Hook up was easy, and he even supplied a set of mating barrel connectors for the flying leads.

From top to bottom:

White = Right Coil

Yellow = Left Coil

Blue = Kill Switch

The source wire pairs were White and White / Blue.

If you put a thin screwdriver down alongside the original twin connector you can push the original spades out and re-use the housing with the new connectors.

The ground was obvious, and went under the original hold-down screw on the left side of the bike. 

(The mounting screw on the right side of the bike was eliminated so that the new Finnbox would sit properly.)

The stator connector was also obvious, and fit directly into the original place, and secured with hook-loop "Velcro" to the inner fender.

The whole Finnbox enclosure was secured to the bike frame with "Velcro" and also zip-tied securely in place.  (Belt and Suspenders) Wires were just the right length to be routed to the original locations, and tied securely in place.

(Ignore that little cube relay, that's for my tail-lamp flasher module.)

Results:

The bike fired up easily after the final termination.  I couldn't wait to test it so I went out right away.

The initial results were very noticeable.  The bike ran evenly on both cylinders while warming up.  There was no misfire present at all.  The requirement for choke was perhaps even shortened as I rode off up the road.  The acceleration at around 4500 rpm went straight through past 5000 rpm with no flat spot or hesitation.  These are all very good results and brought a wide grin to my face.

• Improved - Less misfires when cold
• Solved - No flat spot on acceleration from idle
• Solved - No flat spot or misfire at mid-range engine speed.
• Solved - Pulls like a mule when accelerating hard.... (now I notice the clutch slips a little)
• I haven't been in the rain yet, but I'm fairly sure that was due to weak spark, and should be fine now.

The 300 mile trip I took over this past weekend yielded a respectable 60 miles to the gallon with mostly highway riding.  I don't think I ever could do better than 55 mpg before, and I was keeping up with traffic and the rest of the motorcycle group who all had >900cc bikes.

Long term results of fuel economy are improved, but negligible.  The around-town fuel economy remains about the same in the mid 50's mpg.

Overall a successful and simple upgrade for the average rider, with all the really hard work done by friend and benefactor in Finland Mr. Aki "Andy62" Lötjönen.

Sunbeam S7 Deluxe - swag

I try to snap up any Sunbeam cycle swag whenever I see it.  Paper products are ok, but the condition is usually poor.  Items like this are much more durable and can be enjoyed daily.  The previous owner was kind enough to include the Pioneer Run pennant with the purchase of KYL95.  I keep that hanging in my pool hall.  I picked up the pocket watch a year or so ago on eBay.  (The crystal was missing, so I got it cheap.  Replacement was a snap for an old instrument repair tech like me.)  For a promotional item its hard to beat for uniqueness.

The t-shirt was one of my own creations via an online printing company.  Representing your brand is essential at any bike meet.

The latest addition is the pin.  Its relatively small, and the color is slightly off, but the detail is nice.

If its not Norton, BSA, or Triumph its not something we see on this side-of-the-pond.