Ready for the Long Haul

The Guzzi is ready for a long trip, which I haven't planned yet.  (But I'm ready.)

I got a set of Hebco-Becker bags with mounts intended for an EV.  I had to make a bracket on each side to correct the mounting points for my Aluminum, but they still worked out rather well.  I still need to provide a third mounting point to give the mounts rigidity in the horizontal plane.  I plan to pass a strut behind and attached to the license plate bracket and onto the mounting clasp latchplate.  That should give the extra side-to-side rigidity required.

The bags didn't come with the colored plates which bolt to the outsides of the bag.  I just filled the holes with RTV for the present time.

No more slipping out between the XS650 and the car now.

Next could be a hydraulic clutch???

Petrol Taps

After consulting with the gurus at the ClassicGlory mailing list to confirm the Enots and Ewart type petcocks were rebuildable; I dove right in and stripped them down.  Unfortunately KYL95 has a mismatched set of petrol taps.  Left side is the original Enots type and the right side has a Ewarts valve.

The Enots type came apart easily and it was obvious that the cork seals were the original ones.  There was still a good bit left of them.  Still I'm impressed with the resilience of natural materials such as cork.  I decided to use real cork to replace them since I didn't have any neoprene handy.  The challenge is cutting the wine cork the right thickness, and making the cut parallel.  I managed a couple attempts with limited success until I got the feel for it.  Lengthwise with the grain obviously works better, and some gentle sanding gets it to the correct thickness.  I did a pressurized water test before reassembly and it works fine.  The slider is a bit scarred up, but its still pretty smooth.

The Ewarts type was a bit more challenging.  The rounded cork shape was not something I was prepared to replicate at the moment.  That would mean drilling out the centerpunch and then re-creating the whole brass inside part.  So I cheated.  I clipped the bad edge part of the cork plunger with a razor blade, and fitted a viton o-ring around it so that the o-ring would seal the plunger to the outside and stop it from leaking outside.  It doesn't seal 100% in the closed position, but as long as it doesn't leak down the side of the bike anymore.  I think I'll have to make a more permanent solution here... like maybe the correct Enots valve.

I didn't take photos of the fuel filters taken out of the tank.  I should have since they were a sight.  The right side was nearly blocked with varnish and junk.  The left side had some varnish on in, but wasn't nearly as bad.  A little carb cleaner and some gentle brushing cleaned them up nicely.

Brackets on fork tubes?

Since my own S7 Deluxe is the only one I've ever seen in person, I have nothing to compare it against.  Can anyone tell me what these brackets are supposed to be for on the top of each fork tube?  They rotate under the bolt which closes the top of the fork tube.  There's a small hole in each one where the end is bent up.  What were these intended for?

Guzzi California passenger comfort (part 1)

My wife has complained that the California is uncomfortable and she'd much rather ride on the XS650 as a passenger.  This cannot be!  That's the reason I bought the Guzzi so I could carry both of us in comfort and finally remove that hideous XS750 sissybar from the 650.

The two issues are foot position and seat comfort.  This fix should solve the issue of foot position.  With her riding boots comfortably positioned with the heal against the peg, her toe interferes with my heal.  So, she rides with her toe on the peg with significant discomfort over longer distances  (great for the calf muscle workout however).  So, I saw this article describing the use of stirrup pegs on the rear.  It looks like just the thing.  It gives her heal somewhere to rest and keeps the pipes from receiving melted boot rubber from the heal.  The pegs are Küryakyn Model 8075.  Many thanks to Marina for this accessory tip.